Pin Configuration
DET 1
FB 2
CS 3
GND 4
8 HV
7 NC
6 V DD
5 GATE
Figure 4. Pin Assignments
Pin Definitions
Pin #
1
2
3
4
5
6
7
8
Name
DET
FB
CS
GND
GATE
V DD
NC
HV
Description
This pin is connected to an auxiliary winding of the transformer via resistors of the divider for the
following purposes:
- Generates a zero-current detection (ZCD) signal once the secondary-side switching current
falls to zero.
- Produces an offset voltage to compensate the threshold voltage of the peak current limit to
provide a constant power limit. The offset is generated in accordance with the input voltage
when PWM signal is enabled.
- Detects the valley voltage of the switching waveform to achieve the valley voltage switching
and minimize the switching losses.
A voltage comparator and a 2.5 V reference voltage develop an output OVP protection. The
ratio of the divider determines what output voltage to stop gate, as an optical coupler and
secondary shunt regulator are used.
The feedback pin should to be connected to the output of the error amplifier for achieving the
voltage control loop. The FB pin should be connected to the output of the optical coupler if the
error amplifier is equipped at the secondary-side of the power converter.
For primary-side control applications, FB is applied to connect a RC network to the ground for
feedback-loop compensation.
The input impedance of this pin is a 5 k ? equivalent resistance. A one-third (1/3) attenuator
connected between the FB and the PWM circuit is used for the loop-gain attenuation. FL6300A
performs an open-loop protection (OLP) once the FB voltage is higher than a threshold voltage
(around 4.2 V) for more than 55ms.
Input to the comparator of the over-current protection. A resistor senses the switching current
and the resulting voltage is applied to this pin for the cycle-by-cycle current limit.
The power ground and signal ground. A 0.1 μF decoupling capacitor placed between V DD and
GND is recommended.
Totem-pole output generates the PWM signal to drive the external power MOSFET. The
clamped gate output voltage is 18 V.
Power supply. The threshold voltages for startup and turn-off are 16 V and 10 V, respectively.
The startup current is less than 20 μA and the operating current is lower than 4.5 mA.
No connect
High-voltage startup
? 2010 Fairchild Semiconductor Corporation
FL6300A ? Rev. 1.0.2
3
www.fairchildsemi.com
相关PDF资料
FL7701MX IC LED DRIVER PFC BUCK 8-SOIC
FL7732M_F116 IC LED DRIVER PFC PRIMARY 8-SOIC
FLASHPRO LITE KIT PROGRAMMER FLASHPRO LITE
FLS2100XS IC CTLR FPS HALF BRIDG LCC 9-SIP
FMD15.24G 1500W 24V DC-INPUT 48V RECTIFIER
FMP25.48G 2500W 48V AC-INPUT RECTIFIER
FND850-12DRG FRONT END DC/DC 850W 12V
FND850-12RG FRONT END DC/DC 850W 12V
相关代理商/技术参数
FL633 制造商:BACO Controls Inc 功能描述:
FL-63C 制造商:Showin Technology Co. Ltd. 功能描述:LED LENS LED OPTIC LENS
FL652 制造商:BACO Controls Inc 功能描述:
FL676 制造商:FARADAY 制造商全称:FARADAY 功能描述:Video Oversampling Filters
FL677 制造商:FARADAY 制造商全称:FARADAY 功能描述:Video Oversampling Filters
FL67C7G 制造商:Arcolectric 功能描述:
FL67C7R 制造商:Arcolectric 功能描述:
FL67C8G 制造商:Arcolectric 功能描述: